Key Factors to Prevent Base Distortion and Shrinkage in Large Volume PET Jar Preforms

Key Factors to Prevent Base Distortion and Shrinkage in Large Volume PET Jar Preforms

Manufacturing large-volume PET jar preforms—such as those used for 1-liter to 5-liter confectionery, edible oil, and bulk food containers—presents distinct thermal and mechanical challenges compared to standard lightweight bottle preforms. Because these preforms weigh anywhere from 80 grams to over 250 grams, the wall thickness at the gate and base section often reaches……

PET is an organic polymer with high thermal insulation properties. In heavy wall sections, the outer surface cools and solidifies rapidly against the cold cavity wall, while the internal core remains molten for a longer duration. This volumetric contraction during cooling leads to common defects such as base dishing, sink marks, internal vacuum voids, and gate area distortion.

Preventing these defects requires specific core-cavity tooling geometry, gate temperature balance, and controlled packing phase dynamics.

The Root Causes of Base Deformation in Heavy Preforms

   Heavy Preform Base Cross-Section
  +--------------------------------+
  |    Outer Solidified Shell      |
  |   +------------------------+   |
  |   |  Molten Core Shrinks   |   | --> Causes Internal Voids / Base Dishing
  |   +------------------------+   |
  +--------------------------------+
               ^ Gate Zone

1. Volumetric Thermal Shrinkage

Unfilled PET resin shrinks by approximately $1.5\%$ to $2.0\%$ as it transitions from a melt state ($280^\circ\text{C}$) to a solid room-temperature state. In thick base sections, if hold-pressure is released before the gate center solidifies, material flows backward toward the hot runner nozzle or pulls inward, leaving a concave (dished) base or void.

2. Overheating at the Gate Area

Because all resin enters the cavity through the central base gate, the tool steel surrounding the hot runner nozzle tip absorbs a concentrated thermal load. If the gate cooling block cannot dissipate this heat quickly enough, the preform base remains soft during ejection and warps under mechanical stripper force.

3. Inadequate Core Tip Cooling Velocity

Standard straight-line cooling channels fail to reach the innermost tip of deep preform core pins. When the core tip stays hot, the interior wall of the preform base cannot solidify at the same rate as the exterior wall, creating unbalanced internal stresses.

Tooling Design Strategies to Eliminate Base Defects

1. Optimized Base Radius & Gate Vestige Geometry

A flat preform base concentrate stress and accentuates sink marks. Tooling designers utilize a hemispherical or contoured dome geometry at the base of the preform cavity:

  • Domed Base Contour: Curving the base distributes packing pressure uniformly and compensates for radial shrinkage.

  • Recessed Gate Pocket: Designing a slight recess around the valve gate orifice ensures that any residual gate vestige sits below the baseline plane, preventing the preform from standing crookedly or rocking on flat conveyor lines.

2. High-Efficiency Gate Insert Cooling Circuits

To counteract heat accumulation at the injection point, the gate insert block surrounding the hot runner nozzle must feature an independent, high-velocity cooling circuit:

  • 360-Degree Annular Cooling Channels: Circular water channels machined directly into the gate insert maintain tool surface temperatures between $6^\circ\text{C}$ and $10^\circ\text{C}$ right up to the gate orifice.

  • Separated Thermal Insulation: Utilizing titanium or ceramic insulating rings between the hot runner nozzle tip and the cold cavity gate prevents direct heat transfer from the runner manifold to the cooling water.

Related Precision Tooling Solutions

  • Looking for heavy-duty jar tooling? Explore our dedicated PET Jar Mould manufacturing range built for heavy-grammage preforms.

  • Need high-speed beverage preform tooling? Learn about our engineered PET Preform Mould configurations.

  • Complement your wide-mouth jars with precision caps: Discover our custom PP Cap Mould solutions.

About the Author

You may also like these

Send Inquiry
✖
How can I help you?